3d Subwoofer Enclosure Design Software

If you are just looking to downlaod WinISD and want to skip the overview, you can go directly to the last section of this page

Subwoofer Enclosure Design Software Download Windows
Subwoofer Enclosure Design Software Download Software

Screenshots

Term-PRO is a software package that enables users to design high-performance subwoofer enclosures. Comprehensive Driver Library. 12 types of enclosures. 3 port types. 3D rendering. Blueprints. Requires Windows 7, 8, or 10 & graphics card w/3D. Subwoofer Enclosure Design Freeware. AJ Vented Designer v.2.0. AJ Vented Designer provides an easy to use interface to solve vented or ported box parameters. Can be used for car, truck, sport utility vehicle (SUV), jeep automotive, guitar and home theater applications and projects. Successfully plan, design. File Name:AJ Vented Designer.

The main interface...

Whilst you can only have one graph window open at a time, you can have multiple projects open. This makes it easy to compare different designs.

Working through each Tab on an individual project window

Clicking on the Parameters label toggles the visibilty of the bottom half of the panel(regardless of which Tab you are on)

Box

Dragging vertically on the graphic will change the volume.
Note that the volume shown is the Working Volume,and does not include the space occupied by the driver or ports
Dragging horizontally will change the tuning frequency.
The graphs change as you go.Enter port details on this tab.Set the end correction from the drop-down list showing which ends are flanged**.
In a multi-port design, the vent length shown is for each port
This is also where you can see the frequency of the first port resonance.
Note**: Flanged means flush with a panel. Not to be confused with flared,which WinISD does not support. Once you have your design, you can useBoxnotes or Sonosub to account for flares as well as the volume occupied by the components.

Plot Tab

Use this Tab to set the line width and color for each of your projectsInput power to box.
If using multiple drivers, this is the total power,not the individual power to each driver

EQ / Filter Tab

Add in any filters here.Choose from these with the Add button

Project Tab

Add any notes here Subwoofer Enclosure Design Software Download
Using the Save button usually pre-loads the file name into the save dialog box for you. (unlike choosing Save from the menu)

The three most commonly used graphs...

The most important one.
Watch this as you change box size and tuning frequencyWinISD recommends keeping velocity to 17 m/sec.
This can be refined further by using Flare-itKeep your excursion to Xmax + 10%

Other Graphs available

The other graphs available...

High Pass Filter modelled in WinISD

WinISD has a built in filter section. Access it by selecting the EQ/Filter tab and click the Add button to get this screen. This allows you to model the effects of different filters.
To control cone excursion below the port tuning frequency, it is often neccessary to employ a high pass filter.
A favoured design is the Linkwitz-Riley filter 4th order filter, which is entered as follows:

The 4th order filter has a Q of 0.5 - if you enter any other value, WinISD will ignore it.
To achieve control of excursion without compromising SPL more than neccessary, try different values for the Cutoff frequency. Here is a graph showing how excursion changes with filter design frequency. Xmax is the thin red horizontal line at 9mm

Cutoff frequencies compared

In this example, the blue graph is the one which achieves a maximum excursion of Xmax + 10%

Modelling Boost

The effect of boost can be modelled with the Parametric EQ filter.
The first step is to specify the type of boost.

This example is a Jaycar Amp with 6dB of boost @ 35hz

The software defaults to a Q of 2.0 which seems to be the best fit.
Other values may be more appropriate though - here is how SPL changes with different values for Q

The second step is to set the correct System input power.
WinISD takes whatever you set as the System Input Power and then adds the boost. The result of this process must not exceed the maximum power of your system.
This means that the System Input Power must be set lower than the maximum power by an amount equal to the boost.
The following table shows how much to reduce the power for a given boost

Boost in dB	Divide maximum power by:
1	1.3
2	1.6
3	2.0
4	2.5
5	3.1
6	4.0
7	5.0
8	6.3
9	7.9
10	10.0

As an example, the Blast Furnace is designed for 240w maximum power and has a boost of 6dB.
For 6dB, we must divide the maximum power by 4, so we set the System Input Power to 60w

Setting the input power

As a check that you have got it correct, load a second copy of your project, remove the boost and set the System Input Power equal to your maximum power. Compare the SPL at the boost frequency for the two projects - they should be the same.
Here's our example continued. Red line is 240w with no boost. Green is 60w with 6dB boost @ 35hz. Notice how the two curves are equal at the boost frequency of 35hz

Signal Generator

A signal generator is also included for testing speakers via your sound card and has a range of control options including selecting the frequency from the cursor position on the response graph. If using this function, be careful not to overdrive the output The generator allows you to produce a single frequency, or a sweep across a range.
For the single frequency option, you can manualy specify the frequency, or you can use the cursor to pick the frequency from on of the WinISD graphs.
Unlike some other products, this one doesn't produce any clicks during sweep mode.
There is also an output attenuator, allowing control of the signal level

Attenuator

Recently I have used TrueRTA's spectrum analysis software to have a look at the signal WinISD produces.
TrueRTA has several price / performance options, with this handy oscilloscope function in the free version.
I discovered that the default attenuation of zero, leads to an overdriven situation - at least with my sound card and windows setup.

The following TrueRTA screenshot shows how the signal has the peaks clipped. This produces a whole stream of harmonics. Not the best signal for testing your speakers

Box

The following TrueRTA screenshot shows the results of decreasing the output level from the WinISD tone generator. The clipping is gone and the output is a clean sine wave. Note the vertical scale has been changed from 2 to 1 volt / division

Not Clipping

Setting the Attenuation control to 6 was enough to restore a pristine sine wave. Your results may vary
Now, whenever I use the tone generator, I use TrueRTA to make sure I'm not getting a clipped signal

Flanged vs flared ports

Some people get confused as to the difference between flanged ports and flared ports.
A flanged end is an end that terminates in a flat panel, such as the wall of an enclosure.
A flared end is one that has an expansion section, typically one quarter of a circle in cross-section, to control port noise.
WinISD can factor in flanged ends by applying an end-correction factor. The current version cannot handle flared ends.
Here are some examples...

Since WinISD does not know about flared ports, a manual correction needs to be done. As the following drawing shows, part of the air in a flared port belongs to outside the port. It is generally accepted that half the flare radius needs to be subtracted for each end that is flared. The effective length is what needs to be entered into WinISD.

Effective length of a flared port

Subwoofer Enclosure Design Software Download Windows

Help file and FAQ

The help file and FAQ has all you need to know in order to use the software. WinISD is freeware with a facility to make a donation.

Quick Tip: Entering driver parameters

Driver parameters can be a pain to enter into the database. If you're having trouble getting it to accept parameters, follow this advice from one of the authors....

Try entering just Qms, Re, Mms, Cms, Bl, Sd, hg, hc, Xlim (optional) and Pe. Do not change any parameters the program calculates. That way the data is consistent. You can of course add the dimensional parameters if you like
If you can't get that to work, user Soho54 from AVSforum swears by the following...
Enter the numbers in this order: Sd, Re, Le, Fs, Qes, Vas, Qms, xmax, and then Pe. That's it, now save

Case Study

A case study used to prototype the snorky design illustrates the use of WinISD

Additional WinISD resources

Steve Dart's excellent tutorial on using WinISD including entering driver parameters without errors
A few observations about the various graphs can be found in this discussion at Speakerplans.com
There are quite a few subwoofer driver files at Hometheatershack

While you're here, you might want to check out some free software that compliments WinISD

Whilst WinISD is excellent for designing your working volume, tuning frequency and filter frequencies, there are some things it doesn't do. The following sofware adds plenty of value to your design process.

Boxnotes - check your enclosure design for resonances, factor in the volume taken up by ports and print your cutting list
Sonosub - design a cylindrical subwoofer. Check resonances and clearances
Flare-it, - find the correct port diameter and flare size to avoid audible turbulence
Subsaver - calculator for finding component values for a 2nd-order high-pass filter
QRDude - Software for designing advanced QRD diffusers

You can download WinISD from Linearteam in Finland.

Subwoofer Enclosure Design Software Download Software

This overview describes version 0.50a7 Pro
There is a later version which has similar functionality ie it also calculates box volumes for ported and sealed enclosures using an easy to use interface and also calculates port lengths.
Many graphs are available, including the three used in the Projects section, ie Sound Pressure Level, Vent Air Velocity and Cone excursion, all relative to frequency.

An extensive database of drivers is included and it is easy to add your own entries. This lets you compare different drivers before you go out and spend any money. It is surprising how the final box size and response varies with the driver chosen. Bigger and dearer isn't always the best. Choose wisely, grasshopper!

Car Speaker Box Plans

There are quite a few different enclosure design software programs out there. The prices range from free to $1,000+. For most designs that the novice box builder will attempt there are a few I could recommend:

WinISD - WinISD is made available by LinearTeam. It's a very highly rated, free program for Windows. There is also an online version which isn't as full featured but can be run on any operating system through a web browser. This can be helpful for Mac/Apple users since MacSpeakerz has been discontinued.

Blaubox (click to download) - Blaubox has been around forever it seems. Created by Blaupunkt, it's a DOS program which may cause some run problems with the newest 64bit versions of Windows (try running it in 'compatibility mode'). It's free and definitely worth checking out. It even prints out the cut sheets for your car subwoofer box plans. If you still have trouble running it in compatability mode I'd recommend using a DOS emulator such as DOSBox. It's free and relatively uncomplicated to use.

DISCONTINUED MacSpeakerz - For the Macintosh users without a PC emulator there is a program out called MacSpeakerz. I haven't used it personally but it's fairly popular and virtually the only program made for the Mac. Provided by TrueAudio DISCONTINUED

You should also check out Advanced Enclosure Design and Fabrication . It covers designing enclosures using free computer software, maximizing the output of a subwoofer system, building the box like a pro and testing the output using inexpensive equipment. Click here.

Now that you've seen what's available let's take a look at some of the subwoofer enclosure plans I've created using the software.